2113PAD $175.00 Special Note For 510 Owners: We have detailed instructions and a superb review from Dave Witt who installed a set of our springs. Just ask and we will send it out with your order.3rd PHOTO: and following 2 photos are of a non restored, unmodified, 3rd owner car. We wanted a car that was very original. This car has stock Nissan springs front and rear.The 2nd set of 3 photos were taken with the Super Comp springs installed.Springs were tested using a Larson Flash 36 load tester rated with a 5,000lb cell which cost $90,000. Not tested on a $1,000.00 Summit Nascar cage less spring tester. Wire hardness tested on a US made Newage calibrated Brinell hardness tester 7000.">

Shop a Movie

Customer / Manufacturer Quotes about Datsun Parts

How to use this website

SECURE ORDER FORM

Frequently Asked Questions

Why Buy From Datsun Parts?

Customer Rewards Program

Restoration Products

Nissan/OEM/AfterMarket Differences

Engineering

Ordering, Shipping, Returns, Policies

Warranty Return Policy

Returns / Important

Parts Purchasing Department

Mission Statement

Limits of Liability Statement Important Read

Charitable Giving

Gallery of Fine Cars

Products
Cars For Sale Recommended Installers Lifetime Warranty Special Order Items From Japan Sale Items New Products Consignment Parts New Old Stock Parts Monthly Specials
Parts Category List
Axle Seals Body parts Books / Literature Brakes Brakes 1500 Brake Kits & Packages Cables Carburetor R16 Carburetor U20 Carburetor Kits & Packages Carburetor Mikuni Solex Clutch Cooling Cylinder Head G15/R16 Cylinder Head U20 Dash Differential Electrical Electrical Firing Electrical Switches Electrical Other Emblems Engine 1500/1600 Engine 2000 Engine Timing Components 2000 Engine external Engine Kits & Packages Engine Room Decals & Stickers Engine Seals Exhaust Exterior Trim Fuel Systems Front Axle Gaskets Gaskets Carburetor Gaskets Engine Gaskets Transmission Differential Glass Handles & Latches Heater Interior Interior Trim Z Car Interior Fairlady 310 Interior Interior Kits & Packages Lamps & Lights Locks Knobs Mirrors Rear Axle Rubber Parts Rubber Kits & Packages Soft Tops Steering Steering Kits & Packages Suspension Suspension Kits & Packages Transmission 4 Speed Transmission 5 Speed Transmission Kits & Packages Transmission Seals Used Parts Wheels Weatherstripping Weatherstrip Kits & Packages Wiper & Washer Material & Carpet Swatches

Nissan Parts Dump

Dash Comments

Map to our location

Home

ImagesCategoriesDescriptionPrice








Restoration Products
Suspension
Partnumber: 2113
Datsun Roadster & Fairlady Super Comp Springs - Exclusive Design AFTERMARKET USA

NOTE: Some Datsun 510 owners use our springs to lower the rear of their cars. 410, 411 users for the front

SUPER COMP SPRINGS PASS OUR 100 DOLLAR BILL CLEARANCE TEST WITH 7 QUART NISSAN RACING OIL PAN (SEE PHOTO)

We have received fantastic feedback from everyday drivers and racers alike. Works great with both oil pans with room to spare. No issues with broken oil pans when using OUR comp spring set.

1st PHOTO: Shows a typical Super Comp install complete with our competition sway bar.

Absolutely, positively no alignment, safety issues or geometry problems or wheel fender interference using this lowering kit.

Approved and exclusively used, as the spring of choice, by Spriso Motorsports on all their SR20 conversions.


Rate of this spring is 860 lbs - Length 8.750".

You must shorten your original tall bump stops or buy our short comp bump stops, part number 1890 and shorten them .375 to provide the proper clearance needed between the top of the bump stop to the bottom of the upper control arm. Not shortening the bump stop will cause the bump stop to bottom out creating a harshness in ride. You can also use our part number 2174 urethane spacer under the springs to add more clearance or to adjust the height for street or race use. Free to those who purchase a set of springs, just ask and we will add them into the order.

Using the same vehicle, we completed a extensive, controlled, proper and fair test of this spring as compared with one other manufacturers product currently on the market.Our spring is lowest of them all without question!

Great for racing or on the street!!

To order this spring set with the O-ring pads Order by PART# 2113PAD $175.00

Special Note For 510 Owners: We have detailed instructions and a superb review from Dave Witt who installed a set of our springs. Just ask and we will send it out with your order.

3rd PHOTO: and following 2 photos are of a non restored, unmodified, 3rd owner car. We wanted a car that was very original. This car has stock Nissan springs front and rear.

The 2nd set of 3 photos were taken with the Super Comp springs installed.

Springs were tested using a Larson Flash 36 load tester rated with a 5,000lb cell which cost $90,000. Not tested on a $1,000.00 Summit Nascar cage less spring tester. Wire hardness tested on a US made Newage calibrated Brinell hardness tester 7000.
$135.00 PR

Copyright © 1996-2022 DatsunParts.com. All rights reserved.